Jeep Parts Wiki | Ford Parts Wiki


Home | Search | Browse | Marketplace | Messages | FAQ
Query String
Book Type
Single Book
Books Covering
Books Covering
Books Covering
Book Page Context
usec t pe A bearing the mark AQ ATF Lt ricant Additions heck oil level every 1000 miles with engine idling p king brake set transmission warm and contro le er in Neutral N position ...
minimize corrosive action of battery acid This felt washer should i be saturated with engine oil every 1000 miles fig 2 11 L 1000 MILES F i l I r Fig 2 11 Battery Terminal ...
Washer Lubrication HYDRAULIC BRAKE CYLINDER FLUID LEVEL Every 1000 miles the fluid level in the brake main cylinder should be checked The level of the fluid should be even with the cast boss on inside
Greenbrier 1200 Series CORVAIR 50 Pag Ei One 2 rankcase Oil 2 Crankcase Capacity 2 First 1000 Miles 2 After 1000 Miles 2 SAE Viscosity Oils 2 1 Types of Oils 2 Maintaining Oil Level ...
mileage intervals MINE For Oil Filter add z qt Dry 5 qt Lubrication First 500 to 1000 Miles The engine crankcase of all new vehicles is filled with a special heavy duty oil This ...
will assure the proper break in of the engine components Use this oil only during the first 1000 miles if temperatures CORVAIR SHOP MANUAL
oils described under SAE Viscosity Oils At the end of the first 500 to 1000 miles drain the original oil when hot and refill with an oil of the Viscosity Number and Type indicated below ...
Lubrication After 500 to 1000 Miles After the first 500 to 1000 miles the crankcase oil should be selected to give the best performance under the climatic and driving conditions in the territory in which
both the axle and transPERIODIC M LUBRICANT Differential Carrier The rear axle lubricant should be checked each 1000 miles and replenished as necessary with Multi purpose Lubricant SAE 80 Axle lubricant should be drained ...
replaced at the end of the first 1000 miles to eliminate any loose material from the sump which results from breakin After the initial 1000 drain axle lubricant should be changed seasonally or every
which is below the transmission level and maintain transmission lubrication on grades t Oil Level Check Each 1000 miles check the lubricant of the three RRR speed Transaxle by removing the filler plug ...
Multipurpose gear lubricant should be used Oil Change At the end of the first 1000 miles and each 10 000 miles thereafter oftener under severe dust or service conditions drain both the differential carrier
Automatic 13 BTDC mlic 3 turn Hydraulic 11 1 turn enter lifter to center lifter idle to 1000 RPM 4 to 5 lbs C idle to 1000 RPM 30 to 45 seconds 1 Pint
unnecessary and the housing should not be drained Lubricant level should be checked at every lubrication period 1000 miles When required add steering gear lubricant WORM BEARING ADJUSTER BALLS AND GUIDES WORM SHAFT LOCK ...
Ball Nut Circuits i 107 Fig 4 2 Steering Linkage Lubricate the steering gear linkage every 1000 miles with chassis lubricant Lube points on the steering linkage are located in the ball and socket joints
sump which is below the transmission level thus maintaining transmission lubrication on upgrades Oil Level Check Each 1000 miles check the lubricant of the fourspeed Transaxle by removing the filler plug in the differential carrier ...
used in threespeed gearshift levers ND ADJUSTMENTS Oil Change At the end of the first 1000 miles and each 10 000 miles thereafter oftener under severe dust or service conditions drain both the differential carrier
year around use Lubricant Additions The lubricant level in these units should be checked periodically every 1000 miles To check trans axle unit check first at the axle fig 2 8 if low also check ...
plug hole Lubricant Changes or Refill Drain out the original lubricant at the end of the first 1000 miles and every 10 000 miles thereafter When both units have been emptied for one reason
insoluble in water CLUTCH CONTROL CROSS SHAFT The cross shaft should be lubricated through the fitting every 1000 miles with chassis lube fig 2 3 also coat both ends of shaft ...
under the front bumper to gain access to the filler plug fig 2 4 GENERATOR Every 1000 miles the oiler on each end of the generator should be filled
type cable ciamps from the terminals The positive terminal felt washer should be lubricated every 1000 miles with engine oil CHECKS AND AD JUS1 GENERATOR TELLTALE LIGHT If the indicator light stays on after
MAINTENANCE A LUBRICATION Periodic maintenance of the front suspension includes lubrication of the four spherical joints every 1000 miles and lubrication and adjustment of the front wheel bearings every 10 000 miles See Section
valve thus reducing the possibility of slow leaks through the valve PUNCTURE INSPECTION Every 1000 miles or at each lubrication the tires should be inspected for puncturing objects If such are found they should
Steering Gear Filler Plug EVERY 1000 MfLES r 1 Fig 2 5 Generator Lubrication DISTRIBUTOR A hinge cap oiler on the side of the distribub iousing should be filled with light engine oil evei L000
lube fit tin in the pivot shaft and should be lubricated with ch sis lube every 1000 miles CLUTCH LINKAGE i oat contacting surfaces of clutch spring and lever as mbly with Lubriplate every
SERIES m 611 Models 1205 1206 1244 and 1254 1000 2000 ft lbs Cross Shaft Outboard Lever to Front Engine Mount Clutch Release Bearing Type Sealed Ball Make New Departure Clutch Pilot Bearing Type
electrical connections and condition of the wiring When checking coil test with a reputable tester DISTRIBUTOR Every 1000 Miles Fill hinge cap oiler with SAE 20 oil CHECKS AND ADJUSTI TIMING For efficient operation
company filling stations in sealed containers OIL LEVEL The transmission oil level should be checked every 1000 miles Oil should be added only when the level is near the ADD mark on the dip stick
Pressure should be 4 to 5 lbs and should remain constant at all speeds between idle and 1000 rpm If pressure is too low or too high or varies materially at different speeds the pump
throttle rod and use a universal drive on spark plug socket c Start engine and accelerate to 1000 rpm to blow out loosened carbon NOTE Clearing out carbon in this manner is important in preventing
water consumption exceeding one ounce per cell each 1000 miles In order to obtain the desired setting tailor the voltage regulator setting as follows 1 When the battery uses too much water and the corrected
models e cept for the addition of the relay arm pivot which n xst be greased every 1000 miles ADJUSTMENTS S EERING GEAR FIG 4 34 There are two adjustments necessary to proper perf tmance