| Book | Page | Context |
|---|---|---|
 |
 |
INSULATION ASSEMBLY 1 i FRONT TRIM AND INSULATION ASSEMBLY REAR TRIM AND INSULATION ASSEMBLY Fig 10 100 Rear Seat Compartment Trim BODY EXTERK Perform all servicing operations as explained under four door models except those ... rear pieces of trim secured in position by cement and or finishing screws See Figure 10 100 If original trim is to be reinstalled care should be exercised in detaching trim at cemented locations ... secured by a retainer across the front and three finishing screws at the rear fig 10 100 To remove assembly remove three attaching screws at rear of assembly lift rear of assembly upward and rearward |
|
 |
Door Inner Weatherstrip Replacement 10 99 Door Trim Panel Sealing Tape and Rubber Seal 10 100 Door Handles and Locks 10 100 Outside Handle Replacement 10 100 Lock Handle Replacement 10 100 Lock Assembly Replacement |
|
 |
this section 3 K Kansas City O Oakland W Willow Run 4 Unit numbering will start at 100 001 at all plants Fig 1 11 shows fag for twenty fifth car built at Willow |
|
 |
100 n 9 175 375 500 575 34 14 200 400 550 635 1 e 250 s75 750 e50 1 12 275 650 625 950 CORVAIR SHOP MANU |
|
 |
feet KES n 5 Foot Pedal Type Pendant Mounting On brace under dash Line pressure 100 lb pedal load 840 psi Travel 5 75 PARKING BRAKE Type Mechanical pull rods cables and pulleys operate rear |
|
 |
seating surface the nozzle is either Wose or the seating surface is defective Tighten the nozzle to 100 in lbs approx 8 ft lbs of torque If tightening the nozzle does not eliminate the leak |
|
 |
outlined under Burner Assembly 2 Remove fuel nozzle 3 Install new fuel nozzle and tighten to 100 in lbs approximately 8 ft lbs torque 4 Install louver plate and mixer cup assembly SOLENOID COIL REPLACEMENT |
|
 |
Engine Compartment Side if 99 Plate Engine Compartment Side Rail ansion Front Mounting At Bumper Suspension Front 100 Extension Quarter Inner and Wheelhouse Rear Rear Seat Pan 101 Reinforcement Engine Compartment IS Cover Panel Support |
|
 |
100 71 72 28 54 56S 1e 55 58 59 03 53 80 61 57 4j Fig 10 3 Exploded View of Underh 1 Support Heat Exchanger Bolt 22 Extension Heat 2 Cover Heat Exchanger |
|
 |
assembly By operating these levers in conjunction an unlimited number of settings is possible allowing choice of 100 heated air or any desired proportion and temperature of tempered air During constant high speed driving |
|
 |
AIMER S X TFig 8 100 Aimers and String b Repeat the same operation on the right hand lamp to complete the horizontal adjustment of this pair of lamps HORIZONTAL AIMING SCREW N CENTER STRING |
|
 |
case with the pickup screen positioned parallel to the oil pan rails as shown in Figure 6A 100 Install pickup tube retaining clamp to tube and crankcase as shown in Figure 6A 109 29 Coat |
|
 |
Secure by placing lock washer and nut on back inboard side of flange plate and torque to 100 125 foot pounds 2 FRONT AND REAR Replace the push rods and the brake shoe retracting springs |
|
 |
crossmember into position and align mount ing holes with drift 2 Install mounting bolts torquing nuts to 100 110 ft lbs 3 Install idler arm to frame torquing nuts to 13 22 ft lbs Install |
|
 |
pressure gun equipment It is composed of mineral oil 300 to 500 seconds Saybolt Universal viscosity at 100 F combined with approximately 8y soap or soaps which are insoluble in water CLUTCH CONTROL CROSS SHAFT |
|
 |
provided from the left to the right aimer across the top of the horizontal crossarms fig 8 100 6 Bounce car up and down and roll the vehicle back and forth several times to allow |
|
 |
FRONT WIRING HARNESS O 16 CA BLACK L H HORN 6 100 SERIES HORN 12 GA RED IGNITION SWITCH 14 GA ON GREEN CIRCUIT SHOWN IN STARTING POSITION WINDSH |
|
 |
Compartment Side Rear Seat Pan 99 Spacer Engine Compartment Side Rail le At Bumper if Pan Reinforcement 100 Reinforcement Engine Compartment 1 Side Rail At Bumper r SHELL I CONSTRUCTION known as the unitized type |
|
 |
NOTE It is advisable when taking a long trip to recheck the oil level after the first 100 miles of the trip This is a precautionary measure due to the possibility of crankcase dilution which |